Activity

Microneedle (MN) technology has been proven to be promising to become an effective drug delivery route of insulin for diabetes treatment, with the advantages of high delivery efficiency, convenient management, and minimal risk of infection. However, efforts are still required to verify the insulin activity in MNs for further clinical application. Moreover, it is also essential to study the diffusion properties of insulin to understand the ability of various MN materials to control insulin release. Herein, we have combined all-atom molecular dynamics simulation and coarse-grained dissipative particle dynamics to systematically study insulin’s structural stability and diffusion coefficient in polyvinyl alcohol and hyaluronic acid solutions. The all-atom simulation reveals the dissimilarities in the interaction mode between insulin and the two polymers. It also points out that the presence of the two polymers would not irreversibly impact the secondary structure of insulin, thereby ensuring regular insulin expression in vivo. Mesoscopic simulation results manifest that the diffusion coefficient of insulin in hyaluronic acid (HA) solution is greater than that of the polyvinyl alcohol (PVA) system. Meanwhile, through the study of insulin centroid trajectory, we have claimed two different diffusion mechanisms of insulin in polymer solution The movement of insulin in the HA and water solution follows the Brownian motion rule. In comparison, the hopping effect of insulin has been observed in the PVA solution due to poor intermolecular affinity as well as lower polymer water solubility. By summarizing different diffusion mechanisms, this study can provide theoretical guidance for preparing insulin-loaded dissolvable MNs.This work reports the hybridization of patronite (VS4) sheets with reduced graphene oxide and functionalized carbon nanotubes (RGO/FCNT/VS4) through a hydrothermal method. The synergistic effect divulged by the individual components, i.e., RGO, FCNT, and VS4, significantly improves the efficiency of the ternary (RGO/FCNT/VS4) hybrid toward the oxygen evolution reaction (OER). The ternary composite exhibits an impressive electrocatalytic OER performance in 1 M KOH and requires only 230 mV overpotential to reach the state-of-the-art current density (10 mA cm-2). Additionally, the hybrid shows an appreciable Tafel slope with a higher Faradaic efficiency (97.55 ± 2.3%) at an overpotential of 230 mV. Further, these experimental findings are corroborated by the state-of-the-art density functional theory by presenting adsorption configurations, the density of states, and the overpotential of these hybrid structures. Interestingly, the theoretical overpotential follows the qualitative trend RGO/FCNT/VS4 less then FCNT/VS4 less then RGO/VS4, supporting the experimental findings.Error in Figures 3 and 6 […].In order to optimize the efficiency of the Fused deposition modeling (FDM) process, this study used polylactic acid (PLA) material under different parameters (the printing angle and the raster angle) to fabricate specimens and to explore its tensile properties. The effect of the ultraviolet (UV) curing process on PLA materials was also investigated. The results showed that the printing and raster angles have a high impact on the tensile properties of PLA materials. The UV curing process enhanced the brittleness and reduced the elongation of PLA material. Different effects were observed on tensile strength and modulus of specimens printed with different parameters after UV curing. The above results will be a great help for researchers who are working to achieve sustainability of PLA materials and FDM technology.Biomaterials are widely used for effectively controlling bleeding in oral/dental surgical procedures. LW 6 Here, gelatin methacryloyl (GelMA) was synthesized by grafting methacrylic anhydride on gelatin backbone, and phenyl isothiocyanate-modified gelatin (Gel-Phe) was synthesized by conjugating different gelatin/phenyl isothiocyanate molar ratios (G/P ratios) (i.e., 11, 15, 110, 115, 125, 150, 1100, and 1150) with gelatin polymer chains. Afterward, we combined GelMA and Gel-Phe as an injectable and photo-crosslinkable bioadhesive. This hybrid material system combines photo-crosslinking chemistry and supramolecular interactions for the design of bioadhesives exhibiting a highly porous structure, injectability, and regulable mechanical properties. By simply regulating the G/P ratio (11-115) and UV exposure times (15-60 s), it was possible to modulate the injectability and mechanical properties of the GelMA/Gel-Phe bioadhesive. Moreover, we demonstrated that the GelMA/Gel-Phe bioadhesive showed low cytotoxicity, a highly porous network, and the phenyl-isothiourea and amine residues on Gel-Phe and GelMA polymers with synergized hemostatic properties towards fast blood absorption and rapid clotting effect. An in vitro porcine skin bleeding and an in vitro dental bleeding model confirmed that the bioadhesive could be directly extruded into the bleeding site, rapidly photo-crosslinked, and reduced blood clotting time by 45%. Moreover, the in situ crosslinked bioadhesive could be easily removed from the bleeding site after clotting, avoiding secondary wound injury. Overall, this injectable GelMA/Gel-Phe bioadhesive stands as a promising hemostatic material in oral/dental surgical procedures.The aim of this study was to develop a polyethylene/polyamide (R-PE/R-PA) regranulated product made from post-consumer wastes grafted with polyethylene-graft-maleic anhydride (PE-g-MAH) by reactive extrusion in a twin-screw extruder equipped with an external mixing zone. The compatibility effect of PE-g-MAH used as a modifier in R-PE/R-PA blends was evaluated by means of differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA), while the analysis of the chemical structure of this blend was carried out by Fourier transform infrared spectroscopy (FT-IR). The thermal properties, complex viscosity, and selected usage properties of R-PE/R-PA blends compatibilized with PE-g-MAH, i.e., density and water absorption, were evaluated. The morphology of the blends with and without the compatibilizer was observed by scanning electron microscopy. The R-PE/R-PA/MAH blend shows heterogenic structure, which is a result of the chemical reaction in reactive extrusion between functional groups of PE-g-MAH used as modifier and the end groups of R-PA6.